limiboomer

Specifications Cataloge Specifications: 30' CNC VERTICAL MILL, Bridgeport EZ-Trak SX WITH THREE AXIS DIGITAL READOUT MODEL: EZ-TRAK SX, TABLE WORKING SURFACE.. 9' X 48' NUMBER OF T-SLOTS... 3 LONGITUDINAL (X).. 30' CROSS (Y)...

12' VERTICAL, KNEE (Z).. 5' SPINDLE NOSE TO TABLE. 18-1/4'/2-1/2' MAX./MIN.

Bridgeport EZ-Trak SX. The same problem occurred so I looked in the Manual for the error and here's what. Quick Navigation Bridgeport and Hardinge Mills and. Ebooks bridgeport ez trak manual pdf BRIDGEPORT EZ. Guideand also brother typewriter manuals sx. C6 corvette manual transmission fluidand also.

DISTANCE, CENTERLINE OF SPINDLE TO FACE OF COLUMN. 18-3/4'/6-3/4' MAX UNIFORM TABLE LOAD.. 300 LBS RAM TRAVEL.... Install Itunes Linux Debian System here.

12' HEAD TILT, LEFT AND RIGHT.. 90 DEGREES HEAD TILT, FRONT TO REAR, EACH WAY. 45 DEGREES POWER QUILL FEEDS (3)...0015,.003,.006 IPR INF VAR SPINDLE SPEEDS, TWO RANGES LOW... 60-500 RPM HIGH... 500-4,200 RPM SPINDLE TAPER... R8 MAX COLLET CAPACITY..

3/4' POSITIONING RATE.. 100 IPM X&Y AXES FEEDRATE RANGE, INF VAR. 0.1-100 IPM MIN FEEDRATE INCREMENT.. 0.0001' APPROXIMATE WEIGHT.. 2,340 LBS BRIDGEPORT SX 2-AXIS CNC CONTROL w/ 9' MONOCHROME CONVERSATIONAL DISPLAY, SIMULTANEOUS CIRCULAR OR LINEAR INTERPOLATION, ABSOLUTE AND INCREMENTAL PROGRAMMING, AUTOMATIC CORNER ROUNDING, MATHEMATICAL HELP MODE, CANNED CYCLES FOR MACHINING ARCS, DIAGONALS, CIRCLES, BOLT HOLE PATTERNS, POCKET MILLING AND MORE, CUTTER DIAMETER COMPENSATION, AND ENGLISH/METRIC CONVERSION. PART PROGRAM LOADING IS DONE THROUGH RS-232 PORT or 3-1/2' FLOPPY DRIVE. 256K of memory capacity.

Deux Mondes 6th Edition Isbn 10 on this page. Environment Raven 7th Edition Pdf. THREE-AXIS DIGITAL READOUT DURING MANUAL OPERATIONS DC SERVO MOTORS ON BOTH X & Y AXES BIJUR AUTOMATIC LUBRICATION SYSTEM PNEUMATIC DRAW BAR 2/3 HP 3/60/208-440V SPINDLE DRIVE MOTOR & ELEC. CONTROLS TRANSITION FREELY FROM 2-AXIS CNC TO MANUAL. PERFECT FOR TOOLROOM OR PROTO-TYPE WORK.

After pressing the button to Home the axes at power-up, my 1993 Bridgeport EZ-Trak SX displays the message, 'DRIVES NOT ON, FAILED TO GO HOME'. Last weekend when this problem first occurred, after moving the table and saddle to their limits manually I was able to Home the axes (via the control panel) and the machine then worked normally. (I'm not certain that moving the table and saddle was what made the error go away, as I'm sure I scratched my head a few times in the interim and likely said a prayer or two, too.) Yesterday when I powered up the machine again (it's in a home shop and sits idle most of the time) the same problem occurred so I looked in the Manual for the error and here's what is noted: DRIVES NOT ON, FAILED TO GO HOME!

This message is displayed while attempting to home the axes with power off. I disconnected the (2) connections at the X- and Y-axis drives and reconnected them, but no change. Manually moving to the limits didn't help so I'm hoping that someone on this forum will recognize the error and offer some troubleshooting guidance. Absent that my next step would normally be: disconnect power to the machine, open the power cabinet, unseat and re-seat electrical components and boards, and try again. Thanks in advance for any suggestions! It appears you have control power and the control is smart enough to know the power to the drives is not present.check fuses. If fuses are good then maybe you have an intermittant open in a cable that only happens in a certian area of travel.Thanks for your reply, ProductionPal.

I checked all the fuses today (all were fine) and un-seated, then re-seated, the boards and other components in the electrical cabinet that plug in. Then tested it. And it worked! But only once. After powering the machine off and back on, the problem returned and I've been unable to make it go away again. The cables all look fine but I tried powering it on with the table and saddle at many different locations but the problem persists. Any other ideas?